Tune-up package for all Ruger SA centerfire revolvers: Action job with 3-3 1/4# trigger pull, oversize #5 base pin with lock screw, polish or recut forcing cone and barrel crown, open cyl. throats for cast bullets, alignment check, correct timing as needed, and custom pinned blade front sight base with ramped or patridge style blade.- $850 SS or blue- dual cylinder guns add $100
Bowen rear sight when available- $110-$130
Your choice of any type front sight blade I can make. See bottom of page for upgrade pricing.
To shorten barrel on tune-up package add $200
Set barrel/cyl. gap and endshake to minimum on tune-up package add $150
Correct cyl. endshake add $75
Matte beadblast stainless gun $100
Add colorcased frame, loading gate, & hammer for blued guns to any tuneup package for $425.
All guns sent in for tune-up packages will be checked out thoroughly and you will be notified if any other issues require attention.
Large frame New Model Blackhawks and Older Vaqueros: .44 Special .38-40 10mm 40 S&W .41 Magnum .45 ACP .45 Colt .44 Magnum
New Vaqueros in .357, Flat Tops, and 3 Screws with .357 size frames: .44 Special 10mm 40 S&W .41 Special .41 Magnum .45 Colt (light loads only) .45 ACP .38-40
6 shot caliber conversion- Conversion utilizes a new custom barrel in your choice of length to 7.5" with straight or tapered contour and a factory cylinder. Forcing cone cut to 11 degrees and barrel fitted to minimum barrel/cyl. gap. Cylinder is linebored and rechambered. Custom pinned blade front sight base with .120" wide standard patridge style blade. Old caliber designation will be removed and gun properly remarked. Select caliber from above according to frame size of base gun. Contact me if you need help with this. Base gun must be at least 1 caliber smaller than conversion caliber.
Blue gun- $1595
Stainless gun- $1595
Blue gun with Turnbull colorcased frame, loading gate, & hammer- $1995
Finish options for conversions:
Standard factory equivalent polish- included
High polish blue- add $100
Factory equivalent brushed stainless polish- included
Matte beadblast finish on stainless gun- included
Refinish alloy gripframe- $95
Install bushing in ratchet end of cylinder $75
Belt Mtn. oversize #5 base pin with lock screw $75
Action job $250
Cut Blackpowder chamfer on fluted cylinder $85
Correct cyl. endshake as needed $75
Tighten rotational slack in cylinder by blocking cylinder latch and trigger on NM guns only $350
Steel ejector hsg. $65
Cresent ejector rods for round barrels only- blue or SS $15
Gripframe installation- RW frames only POR
Bowen rear sight when available $110-$130
Linebore and chamber customer supplied auxillary cyl. From $375
Install stainless Bisley hammer on guns with standard gripframe $95 NM guns only
Install stainless Super Blackhawk hammer on guns with standard gripframe $50 NM guns only
The following sight blades are available for pinned bases. All blades are approx. .120" wide. Add $10 for widths thinner than .120". Price shown is the upgrade price. For extra blades add $50 to price.
Standard is black serrated patridge style with 30 degree forward tilt on sight face
Patridge syle with brass bead $30
Post front sight no charge
Post front sight with brass bead $30
Fiber optic in red, yellow, or green $30
Keith style plain black no charge
Keith style with brass bead $30
Black serrated ramped no charge
Patridge style with vertical white line $20
Patridge style with 1-3 gold bars depending on height- $20 per bar. The bars are intended as sighting reference points only.
.44 Special conversion. Shown with optional steel ejector hsg., blackpowder chamfered cyl., Bowen rear sight, and pinned blade front sight.